How do I open my electric gate by hand in a power cut?

A power cut, or a fault that stops the motor, can leave you on the wrong side of your own gate. Most electric gates have a manual release, which disengages the motor so you can push the gate open by hand. Use it when you need to get in or out, and only if your gate's instructions allow it.

Every make is slightly different, so treat this as general guidance, not a substitute for the operation and maintenance (O&M) manual from handover. If you don't have the instructions or a release key, or you're not sure, don't force the gate. Call us, or send a photo or short video on WhatsApp to 07890 387915.

Safety first

Before you touch the release:

  • Make sure everyone, including children and pets, is clear of the gate.
  • Switch off the power to the gate if you can do so safely. Never open the control panel.
  • Only use the manual release if your gate's instructions allow it.

Once the motor is released, the gate can move freely. Electric gates are heavy. On a slope, or in the wind, a swing gate can swing and a sliding gate can roll. Move it slowly and keep control of it, and keep people clear while you do.

If the gate hasn't lost power, and you just want to know why it won't open, start with the safe checks in our guide to what to do when an electric gate won't open.

Find the release and follow your instructions

The manual release is usually a key-operated lock, lever or cover on the motor, or in a release box close to it. On a pair of swing gates there is often a release on each motor.

The exact method varies by make and by motor type. Follow the O&M manual from handover, because it is written for your electric gates. Keep the release key somewhere you can reach if the gate fails, and make sure anyone who needs it knows where it is.

If you can't find the manual, look for a labelled lock or lever on the motor housing, and don't dismantle anything to get to it. If you can't find the release, you haven't got a key, or anything feels stiff or stuck, stop and call us.

Swing gates with arm motors

For many electromechanical arm motors, the process is fairly standard. Find the release lock on the motor, insert the release key and unlock it, then pull out the release lever. That disengages the drive, and you can push the gate open slowly by hand.

Some hydraulic arm motors use a small triangular release key. Insert it and turn it a quarter of a turn. That releases the pressure in the hydraulic ram so the gate can be moved by hand.

If the key won't turn, or the lever won't move, don't force it.

Underground motors

On a swing gate with underground motors, the motor sits in a box in the ground at the hinge, so the release can be less obvious. It is still usually a key-operated release on the motor or in a nearby release point, sometimes under a cover, following the instructions for your system.

Don't lever the motor lid off, or try to disconnect anything in the box. If you can't see a clear release, or the cover is seized, leave it and call us.

Sliding gates

On many sliding gates, the release is on the motor housing beside the track or on the cantilever post. As with electromechanical arm motors, you typically unlock it with the key, operate the lever to disengage the drive, then push the gate open slowly by hand.

A sliding gate can be very heavy, and once released it may roll, especially on a slope. Keep a firm hold, keep people clear of the opening and the run-back, and don't let it run away from you.

Putting the gate back into automatic mode

When you've finished, lock the gate back into automatic mode, or the motor won't drive it. Close the lever or turn the key back, then try the remote, keypad or intercom.

If it doesn't re-engage, don't keep forcing the key or the leaf. A release that's only partly locked back in is a common reason a gate then won't open, or only one side of a pair will move. Call us rather than forcing it.

Power cuts, backup power and solar

If the lights are off in the house, and your neighbours are affected too, it really is a power cut. Some systems have battery backup, so the gate may still open normally for a while. Solar-powered gates run from a panel and a battery at the entrance, so they don't depend on a mains supply at the gate in the same way, though a solar battery can run low after a long spell of poor weather.

If the gate still moves under backup power, use the remote or keypad as usual. You only need the manual release if the gate has no power, or the motor has a fault. If you usually open the gate from your phone, a GSM intercom also needs power and a mobile signal. In a power cut, use the manual release.

If you're unsure, or you need us to look at the gate

We're a Gate Safe Aware Installer, based in Southampton, and we work across Hampshire and the areas we cover. If a gate fails or becomes unsafe, we offer 24-hour call-outs. If you're stuck, send a photo or short video of the motor and the gate by WhatsApp to 07890 387915. Our office hours are Monday to Friday, 8:00am–5:30pm.

A safety systems and gate health check is a good time to go through the manual release and check you have a working key. We force test on every health check, new installation and service visit – see our guides to electric gate force testing and electric gate safety checks.

The health check costs £199 for the first gate or barrier, plus £99 for each additional one checked on the same visit. A pair of double gates counts as one gate. We can also quote a maintenance contract tailored to the site. Electric gates should be serviced at least every six months. A site survey is free for all gates. If the gate is damaged or the motor has failed, see gate repairs.

Frequently asked questions

How do I open my electric gate by hand in a power cut?

If your instructions allow it, switch off the power if you can do so safely, keep everyone clear, use the manual release, and push the gate open slowly. Lock it back afterwards, and never force it.

Where is the manual release on my gate?

Usually on the motor, or in a release box close to it. On underground motors it can be less obvious, often at the hinge. Check your O&M manual for the exact location.

What if I don't have the release key or the instructions?

Don't force the gate or open the control panel. Call us, or WhatsApp a photo or short video of the motor to 07890 387915.

How do I put the gate back into automatic mode?

Close the lever or turn the key back, then try the remote. If it doesn't re-engage, stop and call us rather than forcing it.

Will my gate still work in a power cut without using the release?

It might, if it has battery backup and the battery still has charge, including on some solar-powered systems. If it doesn't move, use the release only if your instructions allow it, or call us.

Next
Next

Why do electric gates need force testing?