An automated gate is a heavy machine that moves by itself, often right where people walk, cars pull in and children play. If it meets a person, a pet or a car, it has to stop and reverse, and the force it applies has to stay within safe limits. Force testing is how an engineer checks that it does.
You can't tell by looking. A gate can open and close every day, look perfectly normal, and still be pushing too hard. That's why this check is done with a calibrated instrument, and why it has to be repeated.
What is force testing?
An engineer uses a calibrated force tester to measure how hard the gate pushes when it meets an obstruction. Readings are taken at set points along the gate's travel, including the closing edge and other places where someone could be crushed or trapped.
The tester records the force, and how quickly that force drops after the gate makes contact. A safe gate should stop and reverse, rather than keep pushing. The results are written down, so there's a record that the gate was checked and what the readings were.
Force testing is not something you can do by eye, or by pushing against the gate with your hand. Please never adjust force settings yourself. If the gate isn't stopping or reversing as it should, keep people clear of it and get it checked.
Why the readings matter
The current British Standard for the safety in use of power operated doors and gates is BS EN 12453. The current UK edition is BS EN 12453:2017+A1:2021. The older test-method standard, BS EN 12445, was merged into BS EN 12453 and withdrawn, so the requirements and the test methods now sit in one document.
That standard sets maximum force levels. The Health and Safety Executive has summarised those maxima as, basically, 400 N for crushing and 1,400 N for impact. HSE also says that where force limitation is the primary means of safety, those forces should be as low as possible, and should be verified by testing after the gate is installed, then checked again later to make sure the gate remains safe.
Those figures are maxima in a standard, not a target. A lower reading is better, particularly where children, older people or anyone less able to get out of the way might use the entrance.
A British Standard is not the same as a law. Powered gates are machinery, and they have to be safe under UK machinery safety law, including the Supply of Machinery (Safety) Regulations 2008 for new gates and for existing gates being motorised. HSE is clear that following the standard alone may not meet every legal requirement, and that each gate needs a proper risk assessment for its site and the people who use it. This is a summary of published guidance, not legal advice.
Passing a force test does not mean a gate is safe
Force testing is an important, objective check, but it is only one part of keeping a gate safe. The UK charity Gate Safe puts it plainly: passing a force test does not, by itself, prove that an automatic gate is safe. A force test measures force at specific points, under specific conditions. It does not cover every hazard.
Other risks include shearing, drawing-in (for example a sliding gate running past a post), trapping at hinges, and gaps between the moving gate and a wall, fence or other structure. On a swing gate, crushing forces can be much higher closer to the hinge than they are at the leading edge. Wind on a solid gate can also change the force from one day to the next.
That's why a safety check also looks at safety edges, photocells and the general condition of the gate, posts, hinges and motors. The most effective approach is to stop people getting into the path of a moving gate in the first place, with non-contact devices such as photocells, and to use safety edges and force limitation as further protection. There's more on what a full check covers in our guide to electric gate safety checks.
Why it has to be repeated
A gate that was within limits when it was fitted can drift out of them. Wear, ground movement, hinge or track problems, dirt, weather, changed settings, or a replaced motor or safety device can all affect how the gate behaves.
That's why we force test on every safety systems and gate health check, every new electric gate installation, and every service visit. If you already have gates and want them automated, the same checks apply when we automate existing gates.
Electric gates should be serviced at least every six months. Busy sites, such as commercial entrances, managed residential blocks, schools, care homes and holiday parks, may need visits more often.
What you get from us
After a new installation, our written handover pack includes:
- the force-testing readings taken at commissioning
- an operation and maintenance (O&M) manual covering how to use, maintain and clean the gate
- a settings book kept in the control panel, so any future engineer can see how the gate is set up
- an electrical certificate, where we carried out the electrical work
After each health check or service, you get paperwork confirming the visit was carried out, and a written report covering any defects, work needed to bring the gate up to standard, and worn parts to budget for, so you can plan ahead rather than face a surprise breakdown. We also check keypads and GSM units as part of the visit.
Our safety systems and gate health check costs £199 for the first gate or barrier, plus £99 for each additional one checked on the same visit. A pair of double gates counts as one gate. We can also quote a maintenance contract tailored to the site. A site survey is free for all gates.
We are a Gate Safe Aware Installer, based in Southampton, and we work across Hampshire and the areas we cover, including on shared gates for landlords and managing agents and on gates for schools, care homes and holiday parks.
If a gate fails or becomes unsafe, we offer 24-hour call-outs. If you're worried about your gate, send a photo or short video by WhatsApp to 07890 387915.
Frequently asked questions
What is electric gate force testing?
It's a measured check, using a calibrated tester, of how hard the gate pushes when it meets an obstruction, and whether it stays within safe limits and reverses as it should.
How often should an electric gate be force tested?
At least every six months, as part of regular servicing, and after any work that could change how the gate behaves. We force test on every safety check, new installation and service visit.
Is force testing a legal requirement?
Force testing is not, on its own, a legal requirement. The legal requirement is that the gate is safe. Where force limitation is used to help keep it safe, HSE says the forces should be verified by testing after installation, and checked again later. A dated report is the practical way to show the check was done.
Does a pass mean my gate is safe?
No. A pass means the measured forces at the test points were within limits on that day. The rest of the gate still needs to be assessed, including photocells, safety edges, hinges, gaps and how the entrance is used.
Can you force test a gate another company installed?
Yes. We check gates whoever installed them.